A phenomenon that can occur from Autumn through Spring is ice dams on the roofs of homes. Ice dams can cause damage to structures that can be very severe. Following is some important information about ice dams, how they can be prevented, and who to call if one should cause damage to your home.

What is an ice dam, and how does it form?

When snow accumulates on a roof, a cycle of melting and refreezing occurs. In a perfect world, the snow would melt off the roof, enter the gutters, and flow harmlessly to the ground. However, two key factors can interact to cause problems: the outside air temperature and the temperature of the inside of your attic.

The warmer your attic is, the more melting will occur. Normally, the resulting water would flow off the edge of the roof. Under certain conditions, though, when outside air temperature is very low, the edge of the roof stays below freezing and the water refreezes when it gets to that point. This ice then forms a line, or “dam,” at the edge of the roof. As more snow melts, it also refreezes when it gets to the “ice dam,” and the dam keeps getting bigger.

Once this dam gets large enough, the melted snow that pools up behind it can force its way back under the roof shingles and then leak into your home!

Contrary to some popular opinions, gutters do not cause ice dams. However, an ice dam can extend into a gutter if weather conditions permit.

How can ice dams be prevented in the first place?

In many instances, the answer is… insulation and ventilation!

InsulatIon

Since the main cause of ice dams is an overly warm attic, a good start in preventing ice dams is to lower the attic temperature. Installing additional insulation in the attic area is as easy as laying additional layers across the existing ones, or having more insulation blown in. However, there are limits to the usefulness of this procedure (diminishing returns), and a professional roofer or insulation person should be consulted if you have any questions. If you notice bare sections on your roof while the rest of the roof has snow, it is an indication there may be insufficient insulation under the bare areas and an inspection of the attic area should be made to confirm this – and then to remedy the situation if necessary.

And, finally, you should also inspect the weather-stripping and/or insulation on attic stairways or hatchways to be sure it is in good shape and seals well. This will help seal the warmth out of the attic area and help prevent ice dams.

VentIlatIon

Even with optimal insulation, there is still heat leakage into the attic. This is when the value of attic ventilation becomes apparent. Without adequate ventilation, heat will build up regardless of the amount of insulation.

First of all, inspect your attic to be sure that the existing vents have not been covered by insulation or other materials or objects. If this has occurred, it is necessary to remove the insulation (or other material) from the soffits so air can move through them freely. The usual recommendation for venting is 1 square foot of vent for every 150 feet of attic floor area.

If your home does not have that ratio (many older homes do not), then you should contact a Contractor to remedy the problem.

If your home does not have vents, consider adding a ridge vent. Again, a professional Roofer or Contractor can give sound advice on the procedure.

If you are not sure about the condition of your roof, you should contact a professional Roofer in your area for advice or assistance.

What are the indicators of an ice dam?

If you notice water damage (marks, drips or lines) on ceilings or exterior walls, it can be an indication that an ice dam has formed, and ice and water have forced their way into your attic area. In addition to fixing the cause of the ice dam, it is important to recognize that this is a true water damage situation that should be remediated by trained professionals, such as PuroClean, to prevent additional damage to the structure (such as rotting), and to prevent the development of mold – a health hazard to people inside of the structure.

Regardless of the circumstances – if water damage occurs from freezing or other sources, call your local PuroClean office. For all water damage, or damage from fire or smoke, PuroClean professionals will mitigate the loss to prevent further damage and then provide restoration services to return the property to a pre-loss condition as quickly as possible. All PuroCleanoffices have professional, well-trained and certified Technicians who provide the latest state-of- the-science services to all property damaged from water, fire, smoke, mold, and other disasters.

written by

Will Southcombe

Director of Technical Services,

PuroClean Headquarters

Master of arts,

Master of Business Management,

Water Restoration technician,

applied structural Drying,

Certified Microbial Remediator

Copyright © 2003-2009. All rights reserved in all countries.

Reproduction of the material is prohibited without prior permission.

Water is a unique substance. As with most materials, when water cools, its density increases and it settles to the bottom of a container. However, at 32º F, it expands and, therefore, its density decreases! This is why ice floats. This expansion increases the volume of water by about 11% and creates tremendous pressure on its container (between 50,000 and 114,000 psi). Such containers include metal and plastic pipes. No matter the strength of a material, expanding water will cause it to break.
Pipes are especially vulnerable to damage caused by expanding water. Water lines that freeze are usually those directly exposed to severe cold, such as outdoor hose bibs, swimming pool supply lines, or water sprinkler lines. In addition, pipes in unheated interior areas such as basements, crawl spaces, attics, garages, and kitchen cabinets, and those that run against exterior walls with little or no insulation are also susceptible to freezing.
A number of variables contribute to freeze damage: the type of building construction; the quality and quantity of insulation; the decline in temperature; the direction and force of wind; and other weather-related conditions are all contributing factors.
Buildings that are poorly designed and do not withstand severe weather sufficiently can contribute to their own damage. The type and age of the plumbing system is also a factor. Rust or corrosion weakens pipes, making leaks more likely to occur. When freeze-expansion occurs, corroded pipes will often split open. When thawing begins or when the water is turned back on, damage can occur.
During renovation of older homes, blown-in or foam insulation is sometimes added to wall cavities between interior and exterior wall surfaces and between studs. This process may actually insulate heat away from pipes adjacent to the exterior wall surfaces, making them more susceptible to freezing.
Surprisingly, pipe freezing can be a particular problem in the warmer climates of southern states. In these areas, buildings may not be adequately constructed for cold weather conditions. Pipes often run through non-insulated or under-insulated attics, crawl spaces, or walls. If the temperature drops below freezing for even a day, these pipes may freeze and break.
In northern climates, many people go south for the winter. They “winterize” their homes by draining the plumbing system and adding antifreeze to plumbing fixtures. This is an excellent prevention procedure and greatly reduces the possibility of frozen pipes.
Draining of a plumbing system should be thorough and complete. If water lines sag or bow, there may be low spots that are difficult to drain completely. To be most effective, compressed air should be used to blow out the lines. If not properly done, some amount of water will remain in the low points of the lines that can freeze.
Damage generally occurs when the water supply is turned back on. Since most modern plumbing lines are inside walls hidden from sight, a freeze-caused leak is usually discovered only after water has damaged floors, carpet, walls, or ceilings. Occasionally, an occupant hears the sound of spraying water, but by then it may be too late. The leak has already caused some degree of damage.
Winter wind, snow, and ice storms frequently damage electric power lines and equipment, resulting in interruptions of electric power. Most heating systems depend on electricity, and when the power goes off, so does the heat. In severe cold weather, this can result in extensive freeze damage before power is restored.
Following are some tips to help prevent damage from frozen pipes when away from your home for more than a day or two:
1. Shut off the water supply and drain pipes or appliances.
2. Have someone you trust check your home about once per week if you are away.
3. Have emergency numbers handy such as a plumber, electrician, roofer, and PuroClean in case something does go wrong.
4. Protect pipes, fittings, and appliances against freezing with insulation or heat strips.
5. Have your HVAC system serviced before leaving if you will be away for an extended period of time.
6. Set your thermostat no lower than 55 degrees.
7. Before leaving turn off your water heater. (See owner’s manual for procedures.)
8. Install storm windows and/or close shutters to keep in heat.
9. Clean gutters and downspouts to ensure proper water drainage.
10. Service sump pump to ensure proper operation. Adding a backup power source is prudent.
11. Unplug all nonessential electric appliances.
12. Inform local police if you will be out of town.
Regardless of the circumstances — frozen or leaking pipes or any water damage, fire/smoke damage, biohazard remediation or mold remediation — call your local PuroClean office, the Paramedics of Property Damage™. For all property damage situations, these professionals are standing by. They will mitigate the loss to prevent further damage and will then provide restoration services to return the property to a pre-loss condition as quickly as possible. All PuroClean offices have well-trained professional technicians who provide the latest state-of-the-science services to all property damaged from water, fire, smoke, mold, and other disasters.

written by
Will Southcombe
Director of Technical Services,
PuroClean Headquarters
Master of Arts,
Master of Business Management,
Water Restoration Technician,
Applied Structural Drying,
Certified Microbial Remediator
Copyright © 2003-2009. All rights reserved in all countries.
Reproduction of the material is prohibited without prior permission.

Property damage caused by freezing weather occurs more frequently and creates greater damage than is commonly thought. When water freezes, its volume increases by approximately eleven percent (11%) and this expansion exerts tremendous force. This force is sufficient to break concrete or even steel! When even a small amount of water enters a structure and freezes, the resulting expansion and weakens the structure allowing more water to enter. The damage cycle continues until the source problem (the initial entry point) is repaired.
A number of variables acting separately or together contribute to freeze damage. A drop in temperature, the type of building construction, the amount and quality of insulation, the direction and force of wind, and other weather-related conditions are all contributing factors.
An occupied building is not completely free from freeze-related damages, even when it is constructed to withstand freezing weather and is properly maintained and heated. However, a significant amount of freeze damage occurs when a building is not occupied, especially if the owners are gone for an extended period, and the heating system is not on during the freezing weather. In northern climates, many people go south for the winter. They winterize their homes before they leave by draining the plumbing system and adding antifreeze to plumbing fixtures. Frequently this is not completely effective, and the owners find freeze damage when they return.
Draining the plumbing system needs to be thorough and complete. If the water lines sag or bow, it can result in a low spot that is nearly impossible to completely drain. To be most effective, draining the water lines should be accompanied by the use of compressed air to blow out the lines. If this is not done, water will rest and freeze in the low points of the lines and may cause the pipes to break. The damage then is discovered only after the water is turned back on and escapes from that break. Virtually all plumbing lines are placed inside of walls and are not visible. As a result, a freeze-caused leak is only discovered when water damage to floors, carpet, walls, or ceilings becomes visible. Occasionally the sound of spraying water can be heard by an occupant, but by then it may already be too late. The leak has already caused some degree of damage.
People living in the south usually consider themselves immune from this type of damage. Because of this sense of security, construction in the southern parts of the country often does not adequately take into consideration that fact that the temperature does occasionally drop below freezing. When that happens and property is poorly insulated, then damage will occur.
Winter wind, snow or ice storms frequently damage electric power lines and equipment resulting in interruptions of electric power. Most heating systems depend on electricity, and when the power goes off, so does the heat. In severe cold weather, this can result in extensive freeze damage before power is restored.
Buildings that are poorly designed and do not withstand weather well can contribute to their own damage. Many old buildings were not insulated at all.
To avoid freezing, plumbing lines were commonly run along the inside of interior walls and ceilings rather than enclosed within the walls. In some cases, many lines simply ran inside of un-insulated walls. During renovation of some old homes, blown or foam insulation has been added into wall cavities between interior and exterior wall surfaces and between each stud. This process many times served to insulate heat away from pipes that were located inside of walls and adjacent to the exterior wall surfaces or in attics, actually making them more susceptible to freezing.
The type and age of the plumbing system is also a factor. Rust or corrosion weakens pipes, making leaks easier to occur. When freeze expansion occurs, such pipes will often split open. As thawing begins or when the water is turned back on, this situation will result in water damage.
There is also a form of direct damage that can occur from extreme cold even though no moisture is present. Most building materials and personal property are unaffected by cold alone, provided they are dry. Extremely cold temperatures can damage some sensitive computer and other electronic components. In northern climates, temperatures commonly fall below zero and occasionally dip to minus 40 to 50 degrees. The contraction associated with those extremely low temperatures can congeal Liquefied Petroleum Gas (LPG) and fuel oil, causing heating system failure.
Regardless of the circumstances— if water damage occurs from freezing or other sources, call your local PuroClean office. These professionals will mitigate the loss to prevent further damage and will then provide restoration services to return the property to a pre-loss condition as quickly as possible. All PuroClean offices have professional, well-trained technicians who provide the latest state-of-the-science services to all property damaged from water, fire/smoke, mold, and other disasters.
written by
Will Southcombe
Director of Technical Services,
PuroClean Headquarters
Master of Arts,
Master of Business Management,
Water Restoration Technician,
Applied Structural Drying,
Certified Microbial Remediator

Copyright © 2003-2009. All rights reserved in all countries.
Reproduction of the material is prohibited without prior permission.

A pipe breaks and now you have wet carpet damage. The insured calls the agent and the process begins. The sooner the policyholder calls the quicker the response and, normally, the lower the total costs of restoration.
Although many issues can be discussed involving water damages, in this article we’re going to concentrate on just one—the carpet. Of all the dollars spent by the insurance industry on property claims, floor covering is, by far, the most expensive category. It stands to reason that if we can save floor coverings affected by water damage the savings, on a national scale, would be significant.
As with any loss, health and safety is of primary importance. The customer should be cautioned about electrical hazards, slip and fall and falling debris, such as drywall or acoustical ceiling tiles.
Quick response is of the essence. The longer the unwanted wet carpet damage is allowed to remain, the more likely the carpeting will experience permanent damage. Because of this, regardless of the hour, the restoration process should begin without delay.

Wet Carpet Damage

Some customers attempt to extract the water themselves. While this can be of some benefit, a shop vacuum, towels and ceiling fans are absolutely no replacement for professional extraction and drying equipment. It is very important to get a professional mitigator on site as soon as possible! The very best opportunity to save carpet (and other items)is to have professionals on site immediately.
The initial stage or phase of the wet carpet damage restoration process includes addressing safety issues and employing “contain and control” procedures. Standing water must be pumped or extracted to prevent migration of water into adjoining areas and sub-surfaces. Professional moisture meters are used to determine the exact location and extent of water damage.
The first step professional restorers take is determining the category of loss: (A) is this a Category-1 loss? (clean watersource;) (B) is this a Category-2 loss? (gray water: with some contamination but not including pathogens or sewage;) or (C) is this a Category-3 loss? (blackwater: involves sewage and known contamination.)
Category-1 is a clean water source and has not come in contact with materials that carry a health concern for the occupants. This would include broken pipes, hot water heaters, tub or sink overflows, etc. professional mitigation specialists can extract water from the carpet and pad and dry them both in place! This dramatically reduces the cost of the claim and helps restore the lives of the policy holders much more quickly.
Category-2 is not a clean water source. This water contains some contamination and has the potential to cause discomfort or sickness if contacted or consumed by humans. Typically this would include washing machine or dishwasher overflows, toilet overflows with no solid matter, broken aquariums, sump pump failures, etc. Because of the additional contamination, this type of loss requires the replacement of the carpet pad, but the carpet itself is normally salvageable. Note: if a Category-2 loss is not treated promptly then the category will escalate to a Category-3 loss (black water.) This is often considered the situation if 48 hours have passed since the loss occurred.
Category-3 is grossly contaminated water containing pathogenic or other harmful agents. Examples of this water include sewage, toilet backflows that originate beyond the toilet trap (regardless of color) all forms of flooding from seawater, rising water from the ground and from rivers or streams, and other water entering the structure from hurricanes, storms or weather-related events.
This water condition is of primary concern when it comes to the health and safety of the occupants. It should be treated seriously because it is serious. Mitigation professionals should be called to deal with this type of loss. Policyholders should not expose themselves to Category-3 water. If, for some reason it is necessary, then they should be reminded to wear gloves, shoe protection and other items to protect themselves.
Carpet is a multi-layered installation with a big sponge under it. Industry standards require that carpet and pad (and anything that is absorbent –textiles, drywall, etc.) that have been contaminated with black water must be bagged and removed from the structure, and disposed of in an appropriate location. Professional restoration companies understand this and operate accordingly.
Every water loss is different. Even with Category-1 andCategory-2 losses, there are varying circumstances that determine whether the carpet can be or should be saved. How old it is, what condition it is in, how it was installed and its construction are all factors that have to be taken into consideration. Mitigation professionals have the training and knowledge to evaluate each situation and to determine the best course of action. They are also trained to communicate well with policyholders, agents and adjusters to insure that everyone understands the process and proper procedures.
So the next time you meet with one of your insureds, take a few moments to explain to them how important rapid response is in the event they were to experience a water loss. Remember, the single most important act in such an event is to call a professional mitigation company to help deal with the loss. Professionals will restore the lives of the policyholders as quickly as possible with maximum cost efficiency and in a trustworthy and understanding manner.
Doug Bowles 4/2007
CCT, CCMT, UFT, WRT, SRT, CRT, RRT
Copyright © 2003-2007. All rights reserved in all countries.
Reproduction of this material is prohibited without prior permission.
This publication provided courtesy of your local PuroClean office.
Offices Independently Owned and Operated.

When water damage occurs in a home, not only are the floors affected, but often drying water damaged walls is difficult. Sometimes the damage is obvious, but in many cases it is hidden and may be missed by those not specifically trained in drying water damaged walls.

For the restoration professional, the first step is to determine the extent of the water damage. Water that enters a room from ground level will cover the floor and floor covering, and will then begin to wick up the wall (move vertically) because of capillary action in porous materials. The extent of this wicking will depend on the construction of the wall, the amount of the water, and its height on the wall material.

Drywall is an absorbent material made of a gypsum core and a cardboard-like paper on both sides. Drywall can wick water up to thirty inches and is very tricky drying water damaged walls! The water will be present on both sides of the wall and often, it is higher on the inside due to restricted evaporation on that side of the drywall. While water damage is sometimes visible, at other times, the wall does not show signs of this moisture.

A restoration professional has a full range of professional metering equipment to help evaluate damage. One choice is a non-invasive moisture meter. This meter uses radio waves to test for the presence of water without putting holes in the wall. Another professional instrument is an infrared imaging device or camera. Since the evaporation from wet walls makes them cooler than dry walls, the IR camera can identify the presence of water in walls — with no holes or other invasion of the wall material.

Once wet walls are identified, drying water damage walls equipment is used to restore them. If there is no insulation present, the walls can usually be dried without holes and without removing the baseboard. The restoration professional places High Capacity Air Movers along the wall every ten to fourteen linear feet. These air movers remove the water molecules from the surface of the wall, allowing further evaporation (drying) to occur as quickly as possible. As the moisture from the wall evaporates into the air, capillary action draws more moisture to the surface where it evaporates.

The restoration professional will also install a Low Grain Refrigerant dehumidifier in the structure — one or more as needed. This state-of-the-science drying equipment reduces the humidity levels to facilitate drying and help prevent the occurrence of mold.

Drying Water Damaged Walls Tips

When appropriate, the restoration professional will install an inner-wall drying system by putting small holes above the sill plate and forcing air into the wall cavity. Studies have shown that this is the best and fastest way to dry walls with water damage.

If there is a moisture barrier on the outside or inside the wall, the drying procedure changes. Moisture barriers are coatings or materials that inhibit the movement of moisture from the wall material. Most latex paints are permeable and do not constitute a barrier. Glossy paints may create a barrier. Enamel paint or vinyl wall coverings create a complete barrier. They will need to be perforated or removed to allow the moisture to escape and the walls to dry.

If there is plastic or foil on the inside of the wall, then the wall will need to be removed since drying will not occur properly and mold will almost certainly develop in such situations.

Insulation in the wall will also affect drying. If there is fiberglass insulation with paper backing, then an inner-wall drying system can be used, as described above. If the insulation is foil-backed fiberglass, blown-in cellulose, or a Styrofoam material, then it cannot be dried successfully. In those cases, removing the damaged portion of the wall along with the insulation is necessary to allow rapid drying and to prevent the development of mold.

Regardless of the procedures used by the restoration professional, it is important that the customer recognize that the equipment must operate, without stopping, throughout the drying process.

A restoration professional will monitor the drying system at least once each day to insure the equipment is operating correctly and to make adjustments as needed. Part of the daily monitoring includes moisture measurements to determine when the materials are successfully dried. Material dryness is measured against similar unaffected materials in that structure. When the levels are the same, the drying is finished and the equipment removed.

A restoration professional, such as PuroClean, understands and uses the principles and procedures of the science of drying to dry walls and other items as quickly and thoroughly as possible, preventing further damage and the development of mold.

Regardless of the circumstances — if water damage occurs from storms, floods, or other sources, call your local PuroClean office, the Paramedics of Property Damage™. For all water damage, or damage from fire or smoke, these professionals are standing by. They will mitigate the loss to prevent further damage and will then provide restoration services to return the property to a pre-loss condition as quickly as possible. All PuroClean offices have well-trained professional technicians who provide the latest state-of-the-science services to all property damaged from water, fire, smoke, mold, and other disasters.

written by
Will Southcombe
Director of Technical Services,
PuroClean Headquarters
Master of Arts,
Master of Business Management,
Water Restoration Technician,
Applied Structural Drying,
Certified Microbial Remediator

Drying water damaged walls can be tricky so leave it up to the professionals.

After a water-damage disaster, restoration professionals are concerned with drying everything as quickly as possible and restoring the property to a pre-disaster condition. This includes being aware of the unique properties of concrete, its reaction to flood conditions, and the unique challenges of drying that material.
When the walls and contents are dried after flooding or other severe water damage, concrete areas are often assumed to be dried as well. New floor coverings are often installed right away. Within weeks, or perhaps months, customers may complain that the newly installed floor is defective. The real culprit, however, is not the flooring, but most likely excessive moisture remaining in the concrete and the condensation that can occur because of the “dew point.”
Dew point is the temperature at which water vapor in the air begins to condense into water (or dew). As the air cools, its ability to hold moisture is reduced. If it continues to cool, eventually the air becomes saturated with moisture and then condenses into water droplets. Normally, a concrete floor is significantly cooler than the rest of the room. Condensation will therefore occur at the surface of the concrete long before it happens elsewhere in the room. Such condensation may form on the concrete even if the rest of the room, walls, and contents have dried to their normal condition.
Many Contractors who are not restoration professionals are unaware of this phenomenon, and move forward with their restoration effort, including the installation of floor coverings.
The damage-and-complaint scenario compounds when water-based adhesives are applied over a damp concrete floor. As moisture evaporates from the concrete, the water-based adhesive absorbs it. This changes the moisture content of the adhesive and prevents it from curing and becoming fixed (or permanent). Since the adhesive fails to become fixed, it will soften and move. Sometimes it appears as bubbles or blisters in certain flooring materials. When tile is applied, the adhesive may ooze or leak out along the edges of the joints or seams. People may believe that the flooring material is defective, but the root cause is premature installation of the floor covering.
The use of water-based adhesives versus solvent-based has increased in recent years due to environmental regulations. Water-based adhesives perform very well under the correct conditions. However, when applied to a substrate with higher-than-normal moisture content, the failure rate increases dramatically.
It is important to contact restoration professionals such as PuroClean when concrete has experienced any type of water damage. Using the latest equipment and procedures, they can determine when the concrete is dry enough. The best method is to use a humidity chamber or humidity box. These are either manufactured boxes or bubbles of plastic taped to the floor.
The chamber traps the moisture released from the concrete, eventually reaching equilibrium. The Contractor carefully inserts a thermo-hygrometer into the chamber and measures the equilibrium humidity. Because concrete is hydrophilic (water-loving) this equilibrium humidity can often be in the upper 60’s. Any reading below 72% is sufficient to install carpet or tile flooring. Wood floors should have readings below 70%.
If the concrete floor needs additional drying, air movement is the best way to hasten the process. Removal of the boundary layer from the surface of the concrete facilitates additional evaporation/drying of the concrete. The room humidity levels will indicate whether a dehumidifier is also needed. If the ambient humidity of the room is below 50%, a dehumidifier is probably not needed, but ongoing monitoring should be done to check for changes.
Please note that each of the respective trades associated with installing floor coverings have established installation standards. All of those standards require the installer to determine that the subfloor (regardless of type) is in a satisfactory condition to allow proper installation of any floor covering.
Regardless of the circumstances — dealing with water damage, fire/smoke damage, or mold remediation — call your local PuroClean office, the Paramedics of Property Damage™. For all property damage situations, these professionals are standing by. They will mitigate the loss to prevent further damage and will then provide restoration services to return the property to a pre-loss condition as quickly as possible. All PuroClean offices have well-trained professional technicians who provide the latest state-of-the-science services to all property damaged from water, fire, smoke, mold, and other disasters.

written by
Will Southcombe
Director of Technical Services,
PuroClean Headquarters
Master of Arts,
Master of Business Management,
Water Restoration Technician,
Applied Structural Drying,
Certified Microbial Remediator
Copyright © 2003-2009. All rights reserved in all countries.
Reproduction of the material is prohibited without prior permission.

PuroClean Technician Receives Certification to Better Service Colorado’s Front Range Property Owners

The “Paramedics of Property Damage” Utilize Continuing Education Tools

Thornton, CO (Grassroots Newswire) 16 Sept 2009 — PuroClean is proud to announce that Toby Click of Aurora, CO recently qualified by education and examination as an Institute of Inspection, Cleaning, and Restoration Certified (IICRC) Water Damage Restoration Technician.

By administering a strict process of certification, the IICRC ensures consumers that they are receiving the highest quality of service from trained, knowledgeable, professional technicians. The IICRC is a nonprofit certifying and standard-setting organization dedicated to raising industry standards through technical proficiency.

PuroClean, a professional mitigation company serving the Colorado’s Front Range community, responds to property emergencies by bringing the damage under control, preventing it from becoming worse, and restoring the property back to pre-loss condition.

“Demonstrating a combination of skill, experience and care when responding to people in their time of need, Toby is an example of what sets PuroClean professionals apart from other mitigation providers,” said Will Southcombe, who heads up training and technical support for PuroClean offices nationwide. “Toby has invested many hours of study to reach this level of certification, which adds tremendous value to the level of service PuroClean Disaster Recovery Experts provides the Colorado’s Front Range community.”

Click joins the ranks of true PuroClean professionals excelling in the mitigation and restoration industry.

About PuroClean
PuroClean is a leader in property damage restoration and has earned the trust of property owners, insurance professionals and home service providers throughout the United States and Canada since 2001. Backed by a comprehensive network of nearly 300 franchise offices and a national training and business support center, each PuroClean office responds promptly to property emergencies demonstrating a high degree of professionalism and compassion. PuroClean certified technicians are thoroughly screened, insured and trained in utilizing the latest in mitigation technology and procedures throughout the remediation process while operating under a strict code of ethics. In addition to serving the needs of property owners, PuroClean offers hundreds of continuing education classes each year to insurance professionals and property service providers nationwide. In 2008, PuroClean trained over 7,200 insurance professionals nationwide helping them earn their continuing education credits. For more information on PuroClean, please contact Mark Wilson at 303-566-9600 or visit

By Will Southcombe
Historically speaking, August and September are the most active months for hurricanes in the Atlantic/Gulf Regions. In addition, there are often severe storms throughout the rest of the nation during these months. All of these events have the potential of releasing record amounts of rain in some areas and causing serious flooding across wide regions.
According to the Institute of Inspection Cleaning and Restoration Certification (IICRC) standard for professional water damage restoration (ANSI/IICRC S500-2006), Category III water damage (often called black water) is water damage to a structure where the origin is unsanitary or potentially infectious to humans. The black water classification also includes less contaminated water not treated in a timely manner. The classification depends on the origin of the water damage and the time of exposure – regardless of the actual color or appearance of the water. Some examples of Category III black water include: all sewage backflows and all rising water from rivers, streams, and seawater that enter a structure. Hurricanes and storms are usually the causes of this type of damage.
When dealing with Category III water damage, a professional restoration business should consider several basic factors. First, the safety of the building occupants and all workers is the primary consideration. Second, the business should conduct a thorough inspection to determine the severity of the damage since that will affect the restoration process. Third, there should be the rapid removal of excess water, the removal of all contaminated porous items, and the proper disposal of the sewage and other wastes. Finally, the professional will need to establish a Balanced Drying System to restore the environment to its pre-loss, normally dry state.
Safety in all instances must be the very first consideration when exposure to Category III contaminates is a possibility. Category III water intrusion could contain many harmful viruses including Hepatitis A, Rotavirus, Adenoviruses, and Enteroviruses. Several parasites and many kinds of harmful bacteria could also be present. And, of course, numerous fungi in the form of mold spores are also present and can become a serious problem if timely decontamination does not occur and if professional drying does not begin within twenty-four to forty-eight hours.
Category III water intrusion can be subdivided into three levels that will help the professional restoration business process the contamination efficiently.
- Category III Level 1 contamination is usually a very limited waste problem. It always originates inside the building or house, affects a small area, does not affect porous material, does not penetrate the structure, and has had limited time of exposure. A small toilet overflow is one example.
- Category III Level 2 contamination also originates inside the building. However, the area of direct contamination is larger. Porous materials as well as non-porous materials are affected. Restoration must be more thorough to include removing moisture barriers like vinyl and plastics that will contain the contamination. Cabinets and other structural enclosures must be inspected and possibly removed if the contamination is present — especially if it is inside the walls behind these items. All contaminated porous items such as drywall, carpet, pad, upholstery, drapery, or particleboard furniture must be removed and properly disposed of.
- Category III Level 3 contamination includes water and waste coming from an outside source such as a septic system, main sewage line, rivers, streams, and ocean waters. Level 3 indicates more contamination for a longer period and presents a much greater health risk.
All black water losses present serious risk of illness. Therefore, contractors should ensure that all employees wear appropriate personal protective equipment. For Level 1 losses, eye protection, gloves, and boots (or shoe covers) may be sufficient. For Level 2 and Level 3 the protection would be more extensive, which could include waterproof coveralls and respirators.
The professional restoration business will know when to use an air scrubber to clean the air, or a negative air machine with containment to prevent contamination from spreading to unaffected areas. They will also make certain that all remaining surfaces are cleaned and sanitized with appropriate cleaners and EPA-approved disinfectants.
Following a Category III black water loss, a professional restoration business will understand and use proper procedures, techniques, products, and equipment (such as professional dehumidifiers and high capacity air movers) to establish a Balanced Drying System to help restore property to its pre-loss condition safely and as rapidly as possible.
In some cases, structural materials may be sealed with an appropriate product to help ensure that contamination does not spread and to help prevent the development of mold.
Regardless of the circumstances – dealing with Category III black water or other water damage, fire/smoke damage, or mold remediation — call your local PuroClean office, the Paramedics of Property Damage™. For all property damage situations, these professionals are standing by. They will mitigate the loss to prevent further damage and will then provide restoration services to return the property to a pre-loss condition as quickly as possible. All PuroClean offices have well-trained professional technicians who provide the latest state-of-the-science services to all property damaged from water, fire, smoke, mold, and other disasters.

Copyright © 2003-2009. All rights reserved in all countries.

’Paramedics of Property Damage’ Help Relieve Stress of Local Property Owners Suffering from Property Damage

Thornton, CO  (Grassroots Newswire) 15 June 2009 –  Home owners suffering from water damage are faced with an extremely stressful experience. PuroClean Disaster Recovery Experts, part of the nation’s fastest growing property damage remediation franchise, is prepared to immediately restore property, relieving the stress of  property owners during an extremely vulnerable time.

Water loss and damage is a real threat for property owners. In fact, according to the Insurance Information Institute in the last year, 22 per 1,000 households have entered a claim for water related damage.  “These situations are more common than most people think,” said Mark Wilson, owner of PuroClean Disaster Recovery Experts.  “Water damage can often result from weather, such as storms or melting snow, or more often, from common household malfunctions such as pipe leaks, washing machine malfunctions or other plumbing problems.”

To help minimize loss, and prevent further damage while technicians from PuroClean Disaster Recovery Experts are en route, Wilson suggests property owners follow these guidelines:
Insurance
o Call your agent.
o Take photographs of the damage.
o Keep all receipts from hotel stays, home repair materials, etc.
Plumbing
o Check pipes on well pumps and irrigation systems.
o If sewage is backing up in the shower or under the toilet, your whole system is backed up. Call a professional and don’t use other sinks or toilets.
Roofing
o If the neighbor’s roof is missing shingles after a storm, you can assume that yours probably is, too.
o If only a few shingles are gone, try to cover the area with a garbage bag.
o If you have a large area of ripped tar paper or wood, cover it with a tarpaulin and call a roofer immediately.
Electric
o Most damage to electrical systems comes from water.
o Appliances exposed to water should be serviced before being used again.
o Check for sparks or frayed wires if wires are exposed call an electrician and do not turn on the power.
o If it appears that water has infiltrated your breaker box, call an electrician.
o Avoid fallen and dangling wires or metal fences.
o If a limb has fallen on a power line, turn off the power and call the utility company.
o If a fallen limb touches your property, it becomes your responsibility, but you should not attempt to clear them as they may be tangled in power lines. Call an electrician.

Flooding (Take these steps to minimize damage before the restoration professional arrives.)
o Throw out all food, including canned goods, medicines and cosmetics that have been touched by flood water.
o Keep a photographic inventory of anything that must be thrown out.
o Don’t take pets into a flooded area and never let them drink standing flood water.

Miscellaneous
o Turn on air conditioner if damage occurs in summer.
o Move valuable paintings, art objects and photos to a safe, dry place.
o Open closet doors, furniture drawers and luggage to aid in drying.
o Remove any wet fabrics and dry immediately.
o Hang furs and leather goods to dry separately at room temperature.
o Stay out of any rooms where the ceiling is sagging from trapped water.
o Turn off the breaker before unplugging appliances.